Archives :: Story Extras :: Tables
September 1, 2012
Contact agitated dryers are used for drying wet powders, slurries, filter cakes, and applications where off-gases during the drying cycle must be contained. If the applications are also heat-sensitive, such as specialty chemicals, polymers, food products and pharmaceuticals, contact drying must take place at low heating temperatures, at residence times in tune with the tolerance of the product, and...
August 1, 2012
The earliest application of the fundamental concepts of fluidization dates back to 16th century when a German scientist (Georgius Agricola) described a process to upgrade ores. However, it was not until the 1930s, with the development of the Winkler coal-gasification process, that commercial use of fluidized beds on an industrial scale was recognized. The need for gasoline during the World War II...
June 1, 2012
Throughout the chemical process industries (CPI), the need to drain a tank or process vessel arises. In batch-type plants, it is a regular occurrence and is one factor that affects the total cycle time per batch and ultimately the entire production capacity of the plant itself. Figure 1. In a vertical cylindrical, flat-bottom tank, liquid is flowing into the outlet nozzle (point 1) located at x...
April 1, 2012
The approaches currently used by process integration specialists to assess the opportunities for the integration of reboilers are frequently erroneous and lead to proposals that have to be rejected at the detailed engineering stages or worse, to commissioned reboilers that do not perform properly. This article examines the integration of both vertical and horizontal thermosiphon reboilers, and covers the...
April 1, 2012
In the chemical process industries (CPI) it is often necessary to verify material specification at various points in the process. In that effort, it is usually impossible — or at the very least impractical — to measure the whole production. Instead, small samples must be extracted from a parent population. Such is the case in particle size characterization of bulk solids, process streams and...
February 1, 2012
Various misconceptions arise when it comes to the thermal design of cooling towers. Sometimes related parameters, such as range, approach, effectiveness, liquid-to-gas ratio ( L/G), wet-bulb temperature, cooling water temperature, relative humidity, number of transfer units (NTU) and other terms create a confusion for the designer in effectively sizing, selecting and evaluating a particular cooling tower...
October 1, 2011
Equilibrium stage simulations are the nearly universal process design tool for mass transfer columns that contact vapor and liquid in countercurrent flow. Whether the service is absorption, stripping, distillation, fractionation, quench or evaporation, equilibrium stage models make mass and heat balances easy. They quickly estimate stream conditions and physical properties. They are easily altered, so a...
September 1, 2011
Dilute-phase conveying systems generally use centrifugal fans and positive displacement blowers for supplying conveying air to the conveying system. However, for some conveying systems, compressed air from a central compressor station is also used. The two important criteria required for pneumatic conveying are air flow and air delivery pressure. Different air movers have different characteristics in the...
May 1, 2011
Due to their simplicity of construction, lack of moving parts, ability to operate at a wide range of temperatures and pressures, low capital and operating cost, cyclones have been the workhorse for gas-solid separation in a wide variety of industries. If properly designed and installed, cyclones can be used to control particulate emissions as low as 5 microns in size, and sometimes to smaller sizes in...
April 1, 2011
Manufacturers of specialty chemicals are routinely required to reduce costs and increase the production of their high-value products. Specifically, competitive pressures from the developing world, increases in raw material costs and volatility in energy costs are putting significant pressure on manufacturers to minimize processing costs and maximize product yields. The economic impact of optimization...
May 1, 2010
A virtually endless number of process options are available for agglomerating powders in the chemical process industries (CPI). These processes can be divided into two main categories: agitation and compression. Agglomeration by agitation includes granulation processes, such as fluidized-bed, disc, drum and mixer granulators. Agglomeration by compression includes compaction processes, such as tabletting...
Get more from ChemEngOnline.com
Get email updates in your inbox
Our LinkedIn group is now over 28,000 members strong!
- Join other CPI professionals from all over the globe and share best practices, expertise, concerns and more.
- Provide feedback to Chemical Engineering Editors
Current members represent Worley Parsons, DuPont, SABIC, Fluor, Air Products, LyondellBasell, Nalco, Dow Chemical, Dow Corning, BASF, Jacobs Engineering, ExxonMobil, Shell, Chevron and more.
We also offer the following subgroup for more targeted discussions: