Mobile Navigation

Environment, Health, Safety & Security

View Comments PDF

Gas Hazard Definitions and Data

| By Chemical Engineering

The detection of gases in plant environments has a critical and wide-ranging role in the chemical process industries (CPI). Among the major applications of gas detection are limiting personnel exposure to hazardous chemicals, preventing explosive atmospheres, protecting the environment and identifying leaks in process equipment. Table 1 summarizes the main reasons for gas monitoring.

 

Table 1.  Summary of the main reasons for gas monitoring.
Type of monitoring Purpose Hazard Possible source of hazard
Personal protection Worker safety Toxic gases Leaks, fugitive emissions, industrial process defects
Explosive Worker safety and facility safety Explosions Presence of combustible gases and vapors due to leaks or process defects
Environmental Environmental safety Environmental degradation Acid gas emissions
Industrial process Process control Process malfunction Process errors
Source: MSA

 

All CPI workers should be conversant with gas-detection terms to promote safety, health and environmental quality. The following is a collection of terms and data involving hazardous gases (Table 2).

Table 2. Exposure data (in ppm) for selected hazardous gases
Chemical and formula Properties PEL
IDLH
LC50
Ammonia (NH3) Corrosive, flammable 50 300 4,000
Boron trifluoride (BF3) Toxic 1 25 806
Bromine (Br2) Highly toxic, corrosive, oxidizer 0.1 3 113
Carbon monoxide (CO) flammable 50 1,200 3,760
Carbon dioxide (CO2)   5,000 40,000 Not available
Chlorine (Cl2) Toxic, corrosive, oxidizer 1 10 293
Chlorine dioxide (ClO2) Toxic, oxidizer 0.1 5 250
Ethylene oxide (C2H4O) Flammable 1 800 4,350
Hydrogen chloride (HCl) corrosive 5 50 2,810
Hydrogen sulfide (H2S) Toxic, flammable 20 100 712
Methyl isocyanate (CH3NCO) Highly toxic, flammable 0.02 3 22
Nitrogen dioxide (NO2) Highly toxic, oxidizer 5 20 115
Phosphine (PH3) Highly toxic, pyrophoric 0.3 50 20
Sulfur dioxide (SO2) Corrosive 5 100 2,520

 

PEL (permissible exposure limit).  Set by OSHA to limit workers’ exposure to an airborne substance, PELs are based on an eight-hour time-weighted average. PELs are enforceable legal limits.

TLV (threshold limit value). Established by the American Conference of Governmental Industrial Hygienists, TLVs are based on known toxicity of chemicals in humans or animals, and are recommendations, rather than legal limits.

IDLH (immediately dangerous to life and health). Defined in the U.S. by the National Institute for Industrial Safety and Health (Part of the Centers for Disease Control and Prevention) as a level of exposure that is likely to cause death or immediate or delayed permanent adverse health effects

LC50 (median lethal concentration). A measure of the toxicity of a surrounding medium that will kill half of a sample population of test animals in a specified period through exposure via inhalation.

Oxygen deficiency

Normal ambient air contains 20.8 vol.% oxygen. When oxygen concentration dips below 19.5 vol.% of the total atmosphere, the area is considered oxygen deficient. Oxygen deficiency may result from O2 being displaced by other gases, such as carbon dioxide, and can also be caused by rust, corrosion, fermentation or other forms of oxidation that consume oxygen. Table 3 outlines the physiological effects of oxygen deficiency by concentration.

If oxygen concentrations in the air rise above 20.8%, the atmosphere is said to be oxygen-enriched. Higher oxygen levels can increase the likelihood and severity of a flash fire or explosion, because the oxygen-enriched atmosphere tends to be less stable than air.

Table 3. Physiological effects of oxygen deficiency by degree
O2 in atmosphere, vol. %
Physiological effect
19.5 to 16 No visible effect
16 to 12 Increased breathing rate; accelerated heartbeat; Impaired attention, thinking and coordination
14 to 10 Faulty judgment and poor muscular coordination; Muscular exertion, causing rapid fatigue; Intermittent respiration
10 to 6 Nausea and vomiting; Inability to perform vigorous movement or loss of the ability to move; Unconsciousness, followed by death
Below 6 Difficulty breathing; convulsive movements; death in minutes
Source: MSA

 

Combustible atmospheres

Vapor and gas. Although these two terms are sometimes used interchangeably, they are not identical. Vapor refers to a substance that, though present in the gaseous phase, generally exists as a liquid or solid at ambient temperatures. Gas refers to a substance that generally exists as a gas at room temperature.

Vapor pressure and boiling point. Vapor pressure can be defined as the pressure exerted by a vapor in thermodynamic equilibrium with its condensed or solid form. Vapor pressure is directly related to temperature, and along with boiling point, determines how much of a chemical is likely to become airborne. Substances with low vapor pressures generally present less of a hazard because there are fewer molecules of the substance to ignite, but they may require higher-sensitivity instrumentation to detect.

Vapor density. Vapor density is the weight ratio of a volume of vapor compared to an equal volume of air. Most flammable vapors are heavier than air, so they may settle in low areas.

Explosive limits. To produce a flame, a sufficient amount of gas or vapor must exist. But too much gas can displace the oxygen in an area, making it unable to support combustion. Therefore, there is a window of concentrations for flammable gas concentrations where combustion can occur. The lower explosive limit (LEL) indicates the lowest quantity of gas required for combustion, while the upper explosive limit (UEL) indicates the maximum quantity of gas (Table 4). Gas LELs and UELs can be found in NFPA 325. LELs are typically 1.4 to 5 vol.%. As temperature increases, less energy is required to ignite a fire and the percent gas by volume required to reach the LEL decreases, increasing the hazard. An environment with enriched oxygen levels raises the UEL of a gas, and the rate of flame propagation. Mixtures of multiple gases add complexity, so their exact LEL must be determined by testing.

References

1. U.S. Dept. of Labor, Occupational Safety & Health Administration (OSHA), 29 CFR 1910.1000 Table Z-1.

2. U.S. Centers for Disease Control and Prevention. National Institute for Occupational Safety and Health (NIOSH). NIOSH Pocket Guide to Chemical Hazards. www.cdc.gov/niosh/npg. Accessed March 2013.

3. Mine Safety Appliances Co., “Gas Detection Handbook” 5th ed. MSA Instrument Div., August 2007.

4. National Fire Protection Association. NFPA 325: Guide to Fire Hazard Properties of Flammable Liquids, Gases and Volatile Solids, 1994.